Sump Filters
Single Element Sump Filters
Series SUS & SRS
FEATURES
- 1″ through 3″ NPTF port sizes
- 5 GPM (19 L/min.) through 150 GPM (568 L/min.) flow ratings
- 60 mesh (262 micron) retention or 100 mesh (150 micron) retention or optional 200 mesh (74 micron)
- Extra large filtering area
- With or without integral bypass valve
- With or without magnet
- Cleanable
OPERATION
Pump draws fluid through filtering medium and contaminants are trapped upon the outer surface. Protection against pump cavitation is given by the SRS filter with built-in bypass valve. Three factory-set pressure settings are available for your bypass requirements.
APPLICATIONS
SUS/SRS bonded sump filters for use with hydraulic oils,
coolants, lubricants and fire resistant fluids. A wide range of equipment
applications include agricultural, construction, industrial, material handling,
chemical, petroleum, machine tool, processing and automated machinery.
Specifications
Ordering Information
Dual Element Sump Filters
Series SU & SR
FEATURES
- Twin-life® dual element filter
- 1″ through 3″ NPTF port sizes
- 10 GPM (38 L/min.) through 150 GPM (568 L/min.) flow ratings
- 60 mesh (262 micron) retention or 100 mesh (150 micron) retention or optional 200 mesh (74 micron)
- Extra large filtering area
- With or without integral bypass valve
- With or without magnet
APPLICATIONS
SU/SR bonded sump filters for use with hydraulic oils, coolants, lubricants and fire resistant fluids. A wide range of equipment applications include agricultural, construction, industrial, material handling, chemical, petroleum, machine tool, processing and automated machinery.
Specifications
Ordering Information
Dual Sump Filters
Pressure Differential/Flow Characteristics
Flow data shown below was taken from laboratory tests using petroleum-base hydraulic oil.
Pressure differentials were measured at the filter outlet fitting.
Mini Sump Filters
FEATURES
- Low cost and compact
- Cleanable wire cloth media.
- Flow rating to 10 GPM (38/L/min.) for all models except 202505, which is raised to 4 GPM (15 L/min.).
APPLICATIONS
Mini sump filters are designed for suction line filtration in fluid power, lubrication, fuel and related systems. Lengths and port sizes differ depending on dirt holding capacity and flow requirements.
ENGINEERING DATA
Nominal Rating: 150 micron
Wire Cloth: Stainless Steel
Fitting and Cap: Aluminum
Construction: Epoxy Bond
Operating Temperature: 275F
(135C) maximum
Service: Most hydraulic fluids
Models other Than 202505
Model 202505
Specifications subject to change without notice.
Mini LINE Filters
SPECIFICATIONS
Element Area:
M-12-P = 12 in.” (77cm)
Filtration: 150 micron
Maximum Pressure: 50 PSI (3.35 Bar)
Fittings: 1/4″ NPTF
MODEL M 12 P9100002
Multi-port Dual Element Filters
Series MS
STANDARD FEATURES
- Choice of 3 outlet ports on 3 models simplifies difficult installation problems.
- Lightweight, rugged cast aluminum construction.
- Eight basic models covering a range from 10 GPM (38L/min.) through 150 GPM (569 L/min.).
- Re-usable, cleanable twin-life® dual element with up to 4 times more filtering area
- Bypass valve isolated in the filter head.
- Vacuum indicator alerts you to filter condition and impending bypass.
OPTIONAL FEATURES
- Viton “O” rings for special applications.
- Any combination of NPTF or SAE flange for outlet ports B, C and D.
OPERATION
Hydraulic fluid flows from the reservoir into the inlet port, continues through the low delta P element and through the outlet port. When the element becomes contaminated, your system is protected against possible wash-off of collected contaminant. Unlike other systems where the bypass flow is forced over the dirt-clogged element, the multi-port filter features a unique bypass valve which is self-contained and isolated in the filter head, and does not depend on the mechanical movement of the sludge covered element. Bypassing fluid flows from the inlet port directly to the outlet port, completely ignoring the dirty element and eliminating the possibility of dumping dirt downstream.multi-port dual element filters
